Air conditioning and split systems
42 servicesStandard split installation 07–09 BTU (up to 25 m²)
Indoor and outdoor unit mounting, up to 3 m line, brackets, 1 wall hole, vacuuming and test run.
Standard split installation 12 BTU (up to 35 m²)
For rooms up to 35 m², up to 3 m line, reinforced brackets, technical hole drilling, vacuuming and commissioning.
Standard split installation 18 BTU (up to 50 m²)
Higher-power splits: reinforced brackets, larger-section line up to 3 m, vacuuming with a two-stage pump.
Standard split installation 24 BTU (up to 70 m²)
Semi-industrial power up to 70 m², up to 3 m line, heavy-duty anchor brackets, commissioning.
2-stage installation — stage 1: chasing and refrigerant line pre-installation
Laying K-Flex insulated copper pipe, cable and drain in the wall chase before finishing. Nitrogen pressure test.
Wall chasing (brick / cellular concrete)
Chasing for the refrigerant line with a wall chaser and dust-free vacuum extraction.
Wall chasing (reinforced concrete)
Diamond chase cutting in reinforced concrete for the AC line, with dust extraction.
2-stage installation — stage 2: unit mounting after finishing
Mounting and connecting indoor and outdoor units on finished walls, circuit vacuuming, commissioning.
Multi-split installation, 2 indoor units
Installing 1 outdoor unit and 2 indoor units in rooms with separate lines.
Multi-split installation, 3 indoor units
Full multi-zone installation with individual line routing for 3 rooms.
Multi-split installation, 4 indoor units
4-zone AC system with a single outdoor unit and circuit vacuuming.
Cassette/ceiling AC installation 07–09 (up to 3.0 kW)
Installation into an Armstrong or grid suspended ceiling, drain and line connection.
Cassette/ceiling AC installation 12–18 (3.0–4.5 kW)
Commercial split installation for offices, shops and restaurants.
Cassette/ceiling AC installation 24 (4.5–6.0 kW)
High output for 50–70 m² commercial spaces.
Cassette/ceiling AC installation 28–36 (6.0–8.0 kW)
Installation of a three-phase or high-power single-phase semi-industrial unit.
Installation on an existing line (up to 3 kW / up to 10 kW)
Installing the unit on existing lines, with testing and vacuuming.
Ducted AC installation 07–09 (up to 3.0 kW)
Concealed installation of the duct unit above a suspended ceiling, without an air-distribution network.
Ducted AC installation 12 (3.0–4.5 kW)
Low-noise concealed climate system for flats and villas.
Ducted AC installation 18 (4.5–6.0 kW)
Medium-pressure duct unit with vibration isolation and line connection.
Ducted AC installation 24 (6.0–8.0 kW)
High-pressure duct unit distributing air to several rooms.
Ducted AC installation 28–36 (8.0–10.0 kW)
High-power concealed climate system for large apartments and offices.
Condensate pump installation (labour and materials)
Installing a continuous-flow or reservoir pump, connected to power and drain.
Dry-trap drain siphon installation
Prevents bad odours from the drain from reaching the air conditioner.
Flexible drain hose installation (1 l.m.)
Laying reinforced spiral drain hose with the correct slope.
Rigid drain pipe installation Ø16–32 mm (PPR)
Reliable welding of rigid polypropylene pipe for concealed condensate drainage.
Wall split maintenance 07–09 with pressure wash and service kit
Indoor unit disassembly, pressure wash in a service cover, antibacterial treatment, outdoor unit cleaning.
Wall split maintenance 12–14 with pressure wash and service kit
Full wash of the heat exchanger and fan wheel, antiseptic treatment against mould and bacteria.
Wall split maintenance 18 with pressure wash and service kit
Deep cleaning of higher-power units, with evaporator and drain tray disinfection.
Drain system cleaning and blow-out
Fixes AC leaks through mechanical and chemical drain clearing.
Antibacterial disinfection and ozone treatment
Eliminates bacteria, mould spores and bad odours with medical-grade products.
AC gas charging (up to 500 g)
Charging labour + gas by electronic scale, with gauge-controlled superheat check.
Nitrogen pressure test (leak search)
Dry nitrogen test up to 30 bar, micro-leak location with an electronic leak detector.
Brazing one leak point (copper-phosphorus)
High-temperature copper pipe brazing with silver filler under nitrogen.
Copper pipe flaring, per joint
Eccentric flaring with cone-face check for joint tightness.
Inverter AC control board repair
Component-level resoldering: IPM power modules, filter capacitors, processors, at the workshop.
Start capacitor replacement (labour and part)
Replacing a failed compressor or outdoor fan capacitor.
Temperature sensor replacement (labour and part)
Replacing the compressor or indoor unit thermistor, with resistance calibration.
4-way valve replacement or repair
Solenoid diagnostics and resoldering of the winter/summer reversing valve.
Split removal with gas recovery (pump down)
Pumping refrigerant into the outdoor unit and carefully removing both units.
Wall split fault diagnostics
€0 if you go ahead with the repair! Gas pressure, electrics, control boards and compressor check.
Multi-split system diagnostics (2–5 units)
Full check of circuit balancing and the outdoor unit's electronic expansion valves.
Ventilation and fresh-air systems
28 servicesWall supply valve installation
Hole up to 160 mm / 50 cm deep, fitting and sealing. Valve and kit not included.
Wall heat-recovery unit installation
Hole up to 200 mm / 50 cm deep, setup and configuration. Unit and power line not included.
Paired wall heat-recovery units installation
Two holes, two units, synchronisation and testing.
Wall heat-recovery unit servicing
Cassette cleaning per instructions, mode check. Filters and repairs not included.
Domestic extract fan installation in existing opening
Fixing, connection, test. No new hole or wiring.
Supply unit installation up to 500 m³/h
Fixing and local connections to pre-prepared services. Unit, network and full commissioning not included.
Supply-extract unit installation up to 500 m³/h
Fixing, anti-vibration mounts, local connections. Duct network and commissioning not included.
Supply-extract unit installation 500–1000 m³/h
Mounting the unit at prepared points. Rigging, network and commissioning not included.
Supply-extract unit installation 1000–2000 m³/h
Mounting the unit at prepared points. Rigging, network and commissioning not included.
Duct fan installation up to 500 m³/h
Fixing and local connection. Fan, duct section and power not included.
Duct fan installation 500–1500 m³/h
Fixing and local connection. Fan, network and power not included.
Roof fan installation
Mounting on a ready-made roof curb with local connection. Curb, roof works and lifting not included.
Removal of accessible ductwork
Dismantling and stacking on site. Haulage, disposal and finishing not included. Minimum €200.
Ventilation unit removal up to 1000 m³/h
Disconnecting services and removing the unit. Special equipment and haulage not included.
Ventilation commissioning up to 1000 m³/h, 10 points
Setup, automation and airflow checks, report. Requires an already-installed working network.
Supply unit servicing up to 500 m³/h
Filter, accessible parts, drive, electrics, modes. Filters, repairs and deep washing not included.
Supply-extract unit servicing up to 1000 m³/h
Two fans, filters, heat recovery core, protections and modes. Filters, belts, washing and repairs not included.
Supply-extract unit servicing 1000–3000 m³/h
Accessible components, adjustment and protection checks. Scope depends on datasheet and dirt level.
Central ventilation filter/cassette replacement (one)
Removing, fitting and securing the replacement. Filter not included.
Plate heat exchanger cleaning
Cleaning the accessible removable cassette per instructions. Complex unit disassembly not included.
Fan belt replacement
Replacement and tension adjustment. Belt not included; pulleys should be checked first.
Duct/centrifugal fan motor replacement
Replacing the accessible compatible motor and testing. Motor, rigging and balancing not included.
Dry mechanical dust duct cleaning
One accessible section, dust containment, cleaning. Disinfection, grease and access hatches not included. Minimum €300.
Grease deposit duct washing
Accessible duct, protective measures and washing. Chemicals, hatches and height access not included. Minimum €350.
Kitchen extractor hood cleaning up to 2 m²
Cleaning the accessible hood, collecting debris. Duct, fan and heavy grease not included.
Extract fan impeller cleaning
Removing accessible dirt and checking rotation. Complex disassembly not included.
Ventilation unit drain pump/siphon replacement
Replacing one accessible component, flow test. Part and new pipework not included.
Heat pumps
5 servicesHeat pump temperature sensor replacement
Fitting a compatible sensor and checking readings. Sensor and extra disassembly not included.
Heat pump fan motor replacement
Fitting a compatible motor and function test. Motor, lifting and complex access not included.
Heat pump compressor replacement
Replacement of the agreed compressor. Compressor, filter and refrigerant not included.
Heat pump plate heat exchanger replacement
Replacing the agreed component per fault assessment. Part and circuit restoration quoted separately.
Smart climate and automation
4 servicesAC factory Wi-Fi module setup
Compatible module, client's app, command testing. Module and subscriptions not included.
AC integration via IR gateway
One device, basic commands, on-site testing. Gateway not included.
Configuration handover and owner training
Backup, access list, guide, session up to 2 h.
* Prices are indicative and may change — use them as a budget reference. The exact cost is set on site, before work starts, and confirmed in the quote.
